BMW E36 Blog

BMW On Board Diagnostics

24th January 2007

BMW On Board Diagnostics

posted in Technical Info, Tips & Tricks |


post rating
PoorOkayGoodGreatExcellent (3 votes, average: 5.00 out of 5)
Loading...

Hello friends,

I found this article about on board diagnostics for your BMW E36 and I thought wow! that’s cool. Unfortunately, I tried to do it on my BMW E36 1993 318is but it didn’t work 🙁 I’m not sure whether I did it right or not, maybe some of you guys will try it. I think it should work, but in my case, I don’t know why it didn’t. Anyway, I shouldn’t forget to thank Jared Fenton, the author of the article. Ready? here it goes:

Disclaimer: Use it at your own risk !!!

Did you know that your BMW 3 Series has an internal diagnostic program built into the computer? Not many people know about this. On the BMW 3 Series, there is a way that you can diagnose common engine problems without having to purchase a code tool or take it to the dealer to have it scanned. This is one of those neat little features of the Service Indicator Computer; the series of lights directly under the tachometer and speedometer that remind you to change the oil and perform service. In this tech article, I will provide you with the procedure for checking the fault codes and what the codes mean. This guide will help you to diagnose any possible problems with your car.

This article is written for both the BMW E30 and E36 3 Series cars (up to 95) and should work on both models where a Service Indicator Computer is used. I will go over the small differences between the early and late cars, as they differ slightly. Keep in mind that this procedure will not work on early cars with Motronic 1.1.

Now on the E30 models, get in the car and put the key in the ignition and turn it to the second turn or �ON� position, but do not start the car. Now, press the accelerator pedal all the way to the floor, then let it release all the way back. Now repeat the depress/release cycle 4 more times fairly quickly, but not too fast. It may take some time to get this timing down correct. It should only take you a few seconds to do this. What this does is activate the wide-open throttle switch and the idle switch 5 times. This then sends a signal to the Motronic ECU to send fault codes to the Service Indicator Light.

On the E36 models, the procedure works the same way, but the timing at which you press/release the gas pedal is faster than on the E30. Just keep at it, and you will eventually get the correct speed.

Watch the �Check Engine� light. It should blink once, and then start blinking a series of four numbers. For instance, say this is a sequence you see� the light blinks once, then twice, then four times and lastly four times. If you read it correctly this means that the SI light is reading out the code 1244 (faulty camshaft sensor) The codes appear as a series of flashes for each digit. The flashes indicating one digit are about one second apart, the next digit will appear after a couple seconds interval. If there are no faults in the car, the computer will flash out the number 1444.

Here is the list of codes and what they indicate.


1211 DME Control Unit

1215 Air Mass Sensor

1216 Throttle Potentiometer

1218 Output Stage, Group 1

1219 Output Stage, Group 2

1221 Oxygen Sensor 1

1212 Oxygen Sensor 2

1222 Lambda Control 1

1213 Lambda Control 2

1223 Coolant Temperature Sensor

1224 Intake Air Temperature Sensor

1225 Knock Sensor 1

1226 Knock Sensor 2

1227 Knock Sensor 3

1228 Knock Sensor 4

1231 Battery Voltage/DME Main Relay

1232 Throttle Idle Switch

1233 Throttle Wide Open Throttle Switch

1234 Speedometer A Signal

1237 A/C Compressor Cut Off

1242 A/C Compressor

1243 Crankshaft Pulse Sensor

1244 Camshaft Sensor

1245 Intervention AEGS

1247 Ignition Secondary Monitor

1251 Fuel Injector 1 (or group 1)

1252 Fuel Injector 2 (or group 2)

1253 Fuel Injector 3

1254 Fuel Injector 4

1255 Fuel Injector 5

1256 Fuel Injector 6

1257 Fuel Injector 7

1258 Fuel Injector 8

1261 Fuel Pump Relay Control

1262 Idle Speed Actuator

1263 Purge Valve

1264 EGO Heater

1265 Fault Lamp (check engine light)

1266 VANOS

1267 Air Pump Relay Control

1271 Ignition Coil 1

1272 Ignition Coil 2

1273 Ignition Coil 3

1274 Ignition Coil 4

1275 Ignition Coil 5

1276 Ignition Coil 6

1277 Ignition Coil 7

1278 Ignition Coil 8

1281 Control Unit Memory Supply

1282 Fault Code Memory

1283 Fuel Injector Output Stage

1286 Knock Control Test Pulse

1444 No Fault Codes
 

I hope you enjoyed this article and I hope it will work for you.

 

Wait for more from . . . BMW E36 Blog

 

Best regards,

Tony Sticks.

Join the BMW E36 Forum

BMW E36 Forum
 

Want to receive exciting tips & information about BMW E36 cars? Enter your Email:-


 

 

Having A Problem With Your Bimmer?

Use JustAnswer Service to get help from a BMW expert now! You can also read my review of this service here.

There are currently 7 responses to “BMW On Board Diagnostics”

Why not let us know what you think by adding your own comment! Your opinion is as valid as anyone elses, so come on... let us know what you think.

  1. 1 On May 11th, 2008, Dkny said:

    I found your site on technorati and read a few of your other posts. Keep up the good work. I just added your RSS feed to my Google News Reader. Looking forward to reading more from you….

  2. 2 On May 12th, 2008, Tony Sticks said:

    @Dkny: Thanks you very much!

  3. 3 On October 26th, 2008, ben said:

    I have a light come on next to the drive light indicator It has a exclimation mark inside a circle with gears. I took it to advance auto and they checked it with a machine and it said i have cylinder 1 and 2 misfire. i replaced both spark plugs and both coils and the car still runs the same loss of power and the light is still on. Do i need to reset the computer and if so how do i do it? I drive a 325i 2001 bmw!

  4. 4 On October 26th, 2008, ben said:

    I have a light come on next to the drive light indicator It has a exclimation mark inside a circle with gears.

  5. 5 On October 26th, 2008, Tony Sticks said:

    @ben: Please check the BMW E36 Warning Lamps. I think your warning light is related to automatic transmission.

  6. 6 On October 19th, 2010, kenneth sansbury said:

    is there a bmw e38 blog?having problem with diagnostic
    of engine? no communication,need repair help?

  7. 7 On April 8th, 2011, ph said:

    after read and try with my bmw 11/1993 e36 M50 but nothing happen How can we,I Known bmw ownner try to search scaner tool and check engine light,and document above said can use instead of scanner tool for me fail ,this fault come from me or procedure is not clear can not follow pls help let it come true

    best regaurd
    ph