BMW E36 Blog

De-Lensing BMW E36 Headlights … DIY

12th June 2012

De-Lensing BMW E36 Headlights … DIY

 
I’ve seen many good looking BMW E36 cars and I always noticed that they have one thing in common. It’s the standard Bosch headlights, but for some reason, the headlights looked a little bit weird. These headlights were actually delensed.

The Bosch original headlights have lenses that will help move the light in the correct directions. Unfortunately, these make the headlights (and the car) look ugly.

I thought that de-lensing is a hard job to do and honestly, I was worried that the result isn’t worth it. After I read about it and found that the job is easy and totally reversible (which is a major point to me), I thought I would give it a try. This is what I did:

1. First, I had to remove the headlights so that I can work on them easily. To do that, I had to start by removing the corner lamps or signal lights. Simply, use a screwdriver to pry the clip that holds the signal light to the main headlight. Then slide it forward carefully.

2. After that, I removed the headlights. It’s an easily job. You can simply reverse what I’ve done in my previous Replacing BMW E36 Headlights post. Just keep in mind that there are 5 screws that hold the headlight. 3 at the top and 2 at the bottom. Remove the screws and slide the headlight forward a little bit so you can disconnect the sockets from the back of the headlight.

After that, remove the headlights completely and put them at a table so you can work on them safely.

3. On each headlight, there are 5 big plastic clips (3 on top and 2 on the bottom). With a flat-head screwdriver, unhook them CAREFULLY. As soon as you’re done, the front part of the headlight should come off.

4. Take a breath and enjoy checking out the reflectors at the back part of the headlight. When the lenses come off, the reflectors will be easier to see from the front of the car which is going to be a sweet look.

5. Notice that both lenses are held in by factory silicone. Using a blade, slice them off. Your lenses should now fall out quite easily. If they don’t, you can use a flat-head screwdriver to gently nudge it out. Be very, very careful!

IMPORTANT: you must keep those lenses (2 on each headlight) in a safe place in case you decide to go back to the old look.

6. Clean the insides of the headlight thoroughly. I sprayed window cleaner then used newspaper to wipe it clean. You may want to wipe the reflector for the low beam as well. I didn’t do that though because it was very clean.

7. Now, hook the front part of the headlight to the rear part carefully (without the lenses of course), and then, put everything back the way it was. Now, you have de-lensed your BMW E36 headlights… Congrats!

8. Last part of this DIY. Did “LIKE” our BMW E36 Blog page on Facebook? If you haven’t done so yet, please do now. Just click the ” periactin online, buy lioresal. LIKE” button below this.

Please leave a comment about whether your car looks better this way or before de-lensing it?

 

BMW E36 Blog: The Ultimate BMW E36 Information Source.

Want to receive exciting tips & information about BMW E36 cars? Enter your Email:-


 

 

posted in Do It Yourself, Exterior, Technical Info, Tips & Tricks, Uncategorized | 1 Comment

11th June 2012

Replacing BMW E36 Headlights … DIY

 

Hello,

If you’ve seen my BMW E36 pictures before, you’d know that I have low quality Chinese headlights. When I bought the car, I knew these headlights are not the best (lighting-wise), but I kinda liked the way they looked and of course the angel eyes with blue circles added to that look. So, I thought that I can’t replace them easily while keeping the car looking as good as it looked back then.

With time, these headlights started to show the marks of age and since they’re made of plastic, they were deteriorating fast. A month or may be 2 ago when I showed you that BMW E36 Headlights Guide, I thought to myself that may be it’s time that I replace those old-dusty-looking headlights with some original ones that are made of glass (this was my top priority). Headlights can be of huge effect on whether the car looks nice or looks old. Since glass headlights are not affected by time (at least, they are better at that than plastic), I made up my mind to get those glass headlights.

Replacing the old headlights with the new stock ones was very easy. If you care to learn how to do it, the most important thing is to keep in mind that there are 5 screws that will hold a headlight in place in BMW E36 cars.

Take a look at this picture. 3 screws at the top and 2 at the sides (bottom).

Lucky me, I found that my old headlights were using only 2 of the top screws to hold the headlight and the two at the sides were missing. So, I removed the 2 screws and the old headlights came out right away.

order paroxetine, clomid online.


There was one catch here which made me realize how lucky I am, otherwise, this replacement task would’ve become a nightmare. The guy who changed the old stock headlights with these one-piece headlights was smart enough not to cut the sockets that were designed to plug into the original stock headlights. Instead, he scratched the wires and used auxiliary wires to connect the headlight wires with the old one-piece headlights. So, this meant that in order to restore everything to its original shape, I had to remove those auxiliary wires and tape the scratched wires. After that, I’ll just plug the sockets into the stock headlights and I’m done.

That’s exactly what I did. Then, I put the headlight in the correct place and slide it there carefully.

Before each headlight sits perfectly in its position, I connected the sockets to the the headlight.

Installing the turn signals was very easy too. The signal light with its socket will fit into the new stock turn signals perfectly. I didn’t have to do anything in there. Just plug them and you’re good to go.

Notice that you’ll have to be extra careful when sliding the turn signals to the side of the headlight. Never ever try to force it into position. If you’ve installed everything correctly, the turn signals will slide in perfectly with small pushing power.

Next, I’ll post about delensing my headlights, but for now, I’ll leave you with these two pictures of the new stock headlights

IMPORTANT: If you’ve not subscribed to the BMW E36 Blog Facebook page, please do using the “LIKE” button below


 

BMW E36 Blog: The Ultimate BMW E36 Information Source.

Want to receive exciting tips & information about BMW E36 cars? Enter your Email:-


 

 

posted in Do It Yourself, Electrical, Exterior, Photos, Technical Info, Uncategorized | 3 Comments

30th July 2007

Cleaning BMW E36 Ellipsoid headlights . . . DIY!

Hi Guys,

 

First of all, let me start today’s post by welcoming our new friend Mortuis Gratis. As you may know, I added the post Welcome BMW E36 blog readers! and I asked the members of this blog to fill in their information in order to get to know each other. The goal is to create a community of BMW E36 enthusiasts. So, if you love BMW E36 cars, and didn’t read that post yet, please do and remember to post your information. I really like hearing from you guys. Until this moment, I received responses from 6 guys and girls + me :-), but of course I’m looking for more E36 lovers.

 

Now for today’s post: In the last couple days, I noticed that my right headlight is getting very dirty and it even started screaming at me to clean it. Every time I see that light, I feel a little guilty for leaving it like this and try to pretend like I didn’t see it. Yesterday, I decided to look up for some information on how to clean BMW E36 headlights and fortunately, I found this DIY (Do It Yourself!) on how this can be done. From the description of the process, it seems quite easy and I’m intending to do it for my car very soon. But, I hope that my headlights can be cleaned in the same way. My car has a totally different headlights, and I’m not sure if this procedure will work on it. But I don’t have anything to lose, so I will try it.

 

You too, if your headlights are dirty or started looking ugly, maybe it’s time for you to do some cleaning. Please read the DIY below and if you have any notes or questions , please let me know.

 

 

Disclaimer: Use this info at your own risk!! I’m not responsible if this didn’t work for you.

1. First, you have to remove your corner lamps. Remove the indicator lamp bulb, then use a screwdriver to pry the clip that holds the indicator lamp free. Slide the indicator lamp out forwards.

 

2. You can now remove the headlights. To do so, you need to remove the 3 screws that are on the top, and two on the side. On my car, they were all Phillips screws. The screw below the indicator lamp area is quite hard to get to. It would probably be relatively easy if you have a short Phillips screwdriver.

 

Pull the headlamp out towards you, then disconnect the connectors. Set your precious headlamp down on a soft, gentle surface!

 

 

3. There will be 2 small metal clips on both the top and bottom of the ellipsoids. Unclip them by prying them off with a flathead screwdriver. Remember to pry from the plastic end because you might break/chip the glass if you apply too much force on it.

 

4. Unhook the 5 big plastic clips (3 on top and 2 on the bottom) with a flathead screwdriver.

 

 

5. You should now be able to separate the lens part from the reflector part of the headlight. Pull them in separate directions. They might be tight, so wiggle them free.

 

6. This is how your headlight will look like when it has been opened:

 

 

7. Notice that both lenses are held in by factory silicone. Using a blade, slice them off. Your lenses should now fall out quite easily. If they don’t, you can use a flathead screwdriver to gently nudge it out. Be very, very careful!

 

 

8. Clean the insides of the headlight thoroughly. I sprayed window cleaner then used newspaper to wipe it clean. You may want to wipe the projector for the low beam as well. Remember to wipe underneath the projector lens! You will see a definite improvement in clarity.

 

9. Make sure you have gotten rid of most, if not all, of the factory silicone. Put the lenses back into their original positions. Double check by looking at the orientation of the other headlight. Now, apply new silicone (I used Selley’s Marine Sealant silicone) to the rim of the lenses (where the factory silicone was before). Let the silicone dry, then make sure the lenses are secure.

 

 

10. Double check for any smudges on the glass, then reassemble in the reverse order of disassembly.

 

Now, let’s make a comparison:

zoloft online, cheap lioresal.

 

Dirty Left Ellipsoid

 

 

Clean Right Ellipsoid

 

 

 

At this point you’ll say “That was worth it!”

 

 

Are you looking for more do it yourself procedures (DIY) ? I recommend the Bentley BMW 3 series service manual for you. I got it and I think it’s a gold mine for us -BMW E36 Owners-. If you didn’t grab your copy yet, get it right now! I’m sure you’ll find this book worth every penny you’ve paid for. Get the Bentley BMW 3 series service manual

 

BMW E36 Blog: The ultimate source of information about BMW E36 cars.

 

Best regards,

Tony Sticks.


Want to receive exciting tips & information about BMW E36 cars? Enter your Email:-


 

 

posted in Do It Yourself, Exterior, Tips & Tricks | 5 Comments