BMW E36 Blog

Let me start this post by welcoming our new friend Denise Wright. As you may know I’ve been trying to make a group of BMW E36 enthusiasts from the readers of this blog. I have posted a previous topic Welcome BMW E36 blog readers! in which I asked everyone who reads this blog to write a little bit about him/her self. So if you didn’t read this post yet please do and lets hear from you. I feel really happy when I hear from you guys.

OK, now for the post of today that I know most of you will like very much. This is a DIY (do it yourself) post which will teach you how to install those cute silver gauge cluster rings on your BMW. I really love the way the gauges look after the installation. I also love this DIY as it’s very simple and can be done by almost anyone who doesn’t have any experience in cars. Let not forget to thank Komodo who wrote this great DIY.

Enjoy the post and lets see how things go with you.

Disclaimer: Use this info at your own risk!! I’m not responsible if this didn’t work for you.

This is a DIY for installing those silver gauge rings you can find all the time on
eBay for about $30-35. Here is an after stock photo of how this mod changes your car. It’s a simple mod, but makes a big difference.

 

 

Tools needed:

– T10 Torque Screwdriver with a long thin handle (one screw is pretty deep inside)

– Phillips head screw driver

 

1) Unscrew the gauge cluster. There are two screws and some friction holding your cluster in. One screw is on each side of the top, as shown in this picture:

 

 

Unscrew those screws and push on the bottom of the glass to loosen the unit. Mine was stuck in there pretty good, so it took a good amount of pressure and jiggling to break it free.

 

2) It should now slide forward and up to the steering wheel.

 

 

IMPORTANT: At this point you’re about to begin messing with electrical parts, so please stop and disconnect your battery before continuing. Leaving it plugged in might make you physically unable to finish this DIY.

 

When you reach behind the unit, you’ll feel three wire bundles connecting it to the car. Two are on the right (one big vertical one, and one small horizontal one just below it), and one big vertical plug is on the left.

 

 

This is probably the trickiest part of the whole installation. You must reach behind the unit (probably blindly) and unplug them, however they are not a normal plug. There’s a little button you must push in the middle of the latch, then slide the clip up until the connection comes lose. Here’s a picture to try and explain it better:

 

 

Then after it’s free just slide it out beside the wheel (again, might require a bit of creative shaking and squeezing, but it’s easily possible.

 

 

3) Now you should have the unit out of the car. Bring it inside or somewhere with good light and go get your T10 torque screw driver. There’s 5 screws, as shown by this image of the back of the cluster. Two up top, one on each side, and one deep screw in the very middle.

 

 

Unscrew them all, pull gently, and the unit should split open:

 

 

4) Now look at the faceplate half of the unit (the top half in the picture above). There are three unique, German engineered, “finger screws” holding the faceplate against the glass. It’s the round black circle knobs on each side, and one in the top middle. To unscrew these, simple twist the white part the direction they will move to free the face plate. Here’s a close up of one of the finger screws:

 

 

5) After all of them are turned to the unlocked/open position, gently pull the faceplate up and it should separate:

 

 

Now simply take your rings and pop them on to the left part of the above picture. Mine were very tight and clipped on, the friction plenty to hold them on through anything, however I know some of the rings are a lot looser and might require some creative glueing to get them to stay.

 

Here’s a picture of the rings on just that piece. Notice the Bugatti Veyron Top Gear on the projector in the background. This is a must for this DIY. If you don’t watch Top Gear while installing the rings, they won’t work.

 

 

6) Now the reverse install. Put the faceplate back in the glass (re-screwing the three thumb screws all the way to ensure nothing moves), then using the torque screws, reattach the back half of the gauge cluster.

 

 

Take it back to your car then, slide it beside the steering wheel, push it firmly into it’s hole, and screw the top two screws in.

 

 

Congratulations, you now have silver gauge rings installed in your car.

 

Are you looking for more do it yourself procedures (DIY) ? I recommend the Bentley BMW 3 series service manual for you. I got it and I think it’s a gold mine for us -BMW E36 Owners-. If you didn’t grab your copy yet, get it right now! I’m sure you’ll find this book worth every penny you’ve paid for. Get the Bentley BMW 3 series service manual

BMW E36 Blog: The ultimate BMW E36 information source.

If you are a reader of my BMW E36 blog, you may have noticed that I mainly blog in 4 or 5 wide topics concentrating mainly on BMW E36 cars (normally because this is a BMW E36 blog … right?). I also post occasionally about BMW news like BMW M3 CSL or BMW E36 on Forza Motorsport 2! which may not necessarily be related to BMW E36 cars. What I’m trying to find out is your opinion about this.  Because you’re the readers of this blog, I must listen to you to know what are the best topics that you would like me to concentrate on in the next few months.

I normally write about:

– Technical Stuff like Do It Yourself posts.

– Videos of burnouts/drifting

– Photos of BMW E36 cars posts which include our models post for the month.

– Fun stuff.

– and about anything else that crosses my mind and I think you will be interested in.

What I want to know is which one of these topics you like me to concentrate on. This doesn’t mean that I will stop posting about the other stuff, but if you like burnout videos for instance, I will try to post more of this type in the future than I used to.

Please use the poll to the right of this post to fill in your preference and thanks in advance for participating.

For those of you who are interested in knowing the results of my previous poll. The result is attached

I hope I will be getting even more response on the new poll than the previous one. Lets hear you guys!

Wait for more from BMW E36 Blog.

Hello,

First of all, let me apologize for not posting this sooner as I promised when I published Funny BMW Advertisements – Part 1. I was very busy in the last couple days and believe me when I say I couldn’t. Everything was set up for the post, but I couldn’t even reserve half an hour to do it. I’m so sorry about that!

OK, if you think that part 1 was good. I agree with you, it really made me laugh especially the "Brings out the boy in you" and the "cats on BMW" ones. But hey, I got more for you and I’m positive you will like those even more. So, here you go. Enjoy the BMW Ads 🙂

Lets hear from you guys. Which ad is the best? I think the "Mercedes Can also bring driving pleasure" is the best LOOOL!

Wait for more from BMW E36 Blog.

Hello,

I have found some funny BMW advertisements in this thread and I thought I would share it with you. I’m sure you will like them very much! This post has the first 20 advertisements. There’s more to come, so stay tuned. I will be posting the second group soon. Mean while enjoy them and let see which one you like best?

Wait for more from BMW E36 Blog.